This is the E-Ink / Paper display device integrated by the image display technology of Microencapsulated Electrophoretic Display (MED). This device has an approach to create a tiny spheres in which the charge color pigments are suspending the transparent electrode
Guide Wiring the 0.95 inch 96×64 RGB OLED Display Module
This is the 0.95 inch 96X64 RGB 65K OLED Display module, driven by SSD1331 via SPI2 Interface distributed by Waveshare. These device is mainly runs on SSD1331 a single chip CMOS OLED/PLED driver at 288 segment and 64 common output
Wiring the SPI 172×72 Gray Shade Electronic Ink (E-INK) Module
This is the E-Ink display module designed for ink display development. This module can work without additional electronic parts you just plug the module directly to your microcontroller. This device has driven by SSD1606 4GS active matrix display driver selectable
Wiring the DRV2605 Haptic Driver for LRA and ERM in I2C/IIC
This is the DRV2605L Haptic Driver for LRA (Linear Resonant Actuator) and ERM (Eccentric Rotating Mass) with effect library and smart loop architecture. This device is licensed version of TouchSense 2200 software from Immersion which eradicates the need to design
Wiring the 128×64 1.3 inch OLED Display on 4 Wire, 3 Wire, i2C Interface
This is the 1.3 inch OLED Display driven by SH1106 from Waveshare, 128×64 resolution, it has integrated 3 interface the 3 wire SPI, 4 wire SPI, and i2C for ease integration in your microcontroller. This OLED is mainly runs by
Wiring and Flashing ESP32-WROVER, ESP WROOM 32 with USB TTL UART and ESP32 Download Tool
ESP32 develop by ESPESSIF systems and some other development module and boards. The ESP32 WROOM 32 is a generic Wifi with Bluetooth, Bluetooth Low Energy Microcontroller module that provides a wide range of applications, from low-power networked sensors at the
The Microchip chipKIT Flip N Click Driven by PIC32MZ Microcontroller
This is a Click Board from chipKIT powered by PIC32MZ microcontroller. This board has the ability to swap out just one elements for alternate or used as entirely runs all your devices with chip kit, it is a great way
Wiring 2N7000 AN10441 as Logic Level Converter for i2C Protocol Devices
Other micro-controller uses 5v as standard input voltage, many latest device modules, popular sensors, GPS, RF modules, Flash Memories, SPI storage, Display, use 3 to 3.3v most of this devices requires logic level conversion to protect them from high voltage
Wiring the MPL3115A2 Altimeter, Barometer, Temperature MEMS i2C / IIC Sensor
Xtrinsic MPL3115A2 provides a microelectromechanical systems MEMS pressure sensor with integrated i2C interface to provide an accurate Pressure / Altitude and Temperature Data. The sensor output are high resolution 24 bit ADC. Internal processing removes compensation tasks from the host
Wiring the ADNS 3050 Optical Navigation Sensor with Microcontroller
This is Avago Technologies ADNS 3050 Module, ADNS 3050 is small form factor entry-level gaming optical navigation sensor. It is packed in an 8 pin staggered dual in line package DIP. It is capable of high speed motion detection typically
Wiring the Winbond W25Q80BV / W25QXX SPI Serial Flash Memory with Microcontroller
The Winbond Flash Memory provides extended megabits and bytes serial flash, used for storage on chip solution system with limited space, pins and power. The W25Q series provides flexibility and enhance performance beyond ordinary Serial Flash Devices. This device are
Wiring the BME280 Environmental Sensor Using i2C/SPI Interface with Microcontroller
BME280 is an integrated digital humidity, pressure and temperature sensor. This sensor module is compact in a small smart integrated device on a metal-led this device runs on a low power consumption that allow the sensor driven in a battery